Distinction between Linoleum and Vinyl Asbestos
To understand the removal of vinyl-asbestos, it is essential to distinguish between linoleum and vinyl-asbestos materials.
Linoleum is a composite material made from oxidized linseed oil mixed with inert fillers such as wood flour, cork dust, and colored pigments, al calendared onto a backing fabric. It was manufactured in England from the late 19th century until the 1960s, after which it was largely replaced by a more cost-effective and durable material: vinyl-asbestos.
Vinyl-asbestos (VA) consists of synthetic polymers, asbestos fibers, and colored pigments, and was commonly produced in the form of square tiles (typically 30×30 cm or 40×40 cm). These tiles were hard, durable, and inexpensive.
This material was widely used from the 1960s to the 1980s in public buildings such as schools, gyms, hospitals, and offices.
Vinyl-Asbestos flooring remediation techniques
Vinyl-asbestos flooring can primarily be remediated using two main methods:
- CONFINEMENT
- REMOVAL
Let’s now take a closer look at these two distinct techniques.
Confinement of Vinyl-Asbestos flooring
This technique falls under Type C encapsulation interventions, as defined by Italian Ministerial Decree dated August 20, 1999. In this case, the asbestos-containing material is stabilized and confined beneath a new overlay (flooring system).
This type of intervention is generally faster and less expensive compared to the removal method, which will be described in the following section.
In summary, the remediation of vinyl-asbestos flooring using the encapsulation technique involves the following steps:
Installation Cycle – Confinement intervention on Vinyl-Asbestos flooring
- Area Preparation
Remove any vinyl-asbestos tiles that are not properly adhered, in compliance with current asbestos regulations.
- Wax Removal (Deceratura)
Eliminate any surface waxes that could impair adhesion of the encapsulating layer.
Apply a layer of GEOSTRIP wax remover using a mop or cloth, allow it to act for 15 minutes, then remove using a single-disc machine or a soft pad.
- Reinforcement Mesh
Lay the HYDRONET reinforcement mesh across the entire floor surface to be treated, ensuring an overlap of at least 2 cm at the edges of each roll.
- Encapsulation Layer
Apply a zero-thickness skim coat of CEMBLOK FILM C over the mesh using a squeegee, flat trowel, or airless sprayer.
The squeegee and trowel offer fast application without smudging walls.
Consumption: 0.9 kg/m²
Dilution: Ready to use
- Flooring Selection
After waiting at least 48 hours to allow the CEMBLOK FILM C + HYDRONET system to fully cure and bond with the vinyl-asbestos flooring—forming a single, stable layer—you may proceed with the installation of one of the following flooring types:
- a) Resin Flooring – COLORPAVING
Apply at least two coats of COLORPAVING EPOX RASO PAVIMENTO self-levelling epoxy resin using a flat trowel.
Consumption per coat: 1.2 kg/m²
Waiting time between coats: 12–18 hours
Within 48 hours of applying the final coat, sand the surface using a single-disc machine and sandpaper to remove any ridges or unevenness.
Then apply two coats of COLORPAVING VERNICE PU colored polyurethane finish (glossy, satin, or matte), using a roller.
Consumption per coat: 0.15 kg/m²
- b) Bonded Flooring
Before laying the new flooring over the treated surface, apply one coat of GEOGRIP ECO adhesion promoter using a roller.
Consumption: 0.3 kg/m²
Dilution: Ready to use
- c) Floating Floor
In this case, no adhesion promoter, GEOGRIP ECO, is required.
The floating floor is laid directly over the CEMBLOK FILM C + HYDRONET system.
Bill of Quantities – Technical Specification for the confinement of Vinyl-Asbestos flooring
| No. | Description of works | Quantity (m²) |
Unit Price (€) |
Total amount (€) |
|---|---|---|---|---|
| 1 | Removal and disposal of non-adhering vinyl-asbestos tiles from subfloor | |||
| 2 | Wax removal using GEOSTRIP wax remover by Geo Hydrica S.r.l. Application and removal | |||
| 3 | Installation of HYDRONET reinforcement mesh by Geo Hydrica S.r.l., with 2 cm overlap on all sides | |||
| 4 | Encapsulation by confinement using CEMBLOK FILM C encapsulant by Geo Hydrica S.r.l. Consumption: 0.9 kg/m² |
|||
| 5 | Curing time for system (48h) Site management costs |
|||
| 6 | Application of universal adhesion promoter GEOGRIP ECO by Geo Hydrica S.r.l. Consumption: 0.3 kg/m² |
Bill of Quantities – Specification for seamless resin flooring over Vinyl-Asbestos flooring
| No. | Description of works | Quantity (m²) |
Unit Price (€) |
Total Amount (€) |
|---|---|---|---|---|
| 7 | Trowel-applied leveling skim coat with epoxy resin, type COLORPAVING EPOX RASO PAVIMENTO by Geo Hydrica S.r.l. 2 coats at 1.2 kg/m² |
|||
| 8 | Sanding of the flooring using a single-disc machine and sandpaper | |||
| 9 | Decorative finish applied by roller with colored polyurethane coating, type COLORPAVING VERNICE PU by Geo Hydrica S.r.l. 2 coats at 0.15 kg/m² |
|||
| 10 | Curing time for pedestrian traffic (2–3 days) Site management costs |
Removal of vinyl-asbestos flooring
Before any intervention, it is mandatory to apply a certified Type D encapsulating solution to the vinyl-asbestos flooring, such as CEMBLOK BASE by Geo Hydrica srl, in order to fix any free or potentially releasable asbestos fibers. After this step, the tiles can be removed using mechanical detachment and packed in approved bags. Once this phase is complete, the residual adhesive,often containing asbestos fibers either due to its original composition or due to fiber release from the underside of the tiles must also be removed.
This removal can be carried out in two very different ways:
- Mechanical abrasion using diamond discs – this traditional method exposes the operator to asbestos fibers, making dynamic confinement and air filtration mandatory.The conventional mechanical removal of adhesive through abrasion is well documented in the literature. However, in the following pages, we focus on a more eco-friendly and safer solution, the result of research and innovation by our laboratories.
- Chemical degradation of the adhesive – an eco-friendly, innovative, and non-hazardous method that uses REMOVECO, a gel based on biodegradable and non-hazardous substances.
REMOVECO is a high-performance gel specifically designed to dissolve the polymer matrix of adhesives. Its stable, non-drying formulation keeps the substrate moist, reducing the risk of airborne fiber release.
Before application, it is recommended to carry out a preliminary test on a small sample area to verify effectiveness. Some adhesives, particularly those rich in synthetic polymers, may be less reactive to REMOVECO and may not fully dissolve.
Only after confirming the success of the test should the full-scale intervention proceed.
Advantages of REMOVECO
- No mechanical abrasion required - REMOVECO GEL eliminates the need for adhesive grinding, drastically reducing exposure to airborne asbestos fibers. The gel does not evaporate, keeps surfaces wet, and encapsulates asbestos fibers, preventing their dispersion. Treated cement surfaces can be recovered and reused.
- No need for dynamic containment - Thanks to the safe formulation of REMOVECO GEL, which poses no risk to humans or the environment, and the absence of abrasive operations using diamond discs, it is possible to evaluate—together with regulatory authorities—the use of static containment instead of dynamic containment.
- Reduced intervention costs and time -The use of REMOVECO GEL leads to significant savings in site setup costs and allows for faster execution, making the process more efficient and sustainable.
Application cycle – Removal of vinyl-asbestos adhesives via chemical degradation
Application
After removing the vinyl-asbestos tiles and treating the surface with CEMBLOK BASE encapsulant, apply a uniform layer of REMOVECO GEL directly onto the adhesive using one of the following tools:
- A long-handled soft-bristle brush
- A triangular-notched squeegee (max 1.5–2 mm)
- An airless spray pump
- A wide flat brush (for small surfaces or complex details)
Initial Gel soaking phase
Let REMOVECO GEL act for 4–6 hours. During this time, the polymer matrix of the adhesive breaks down chemically, turning into a wet, gel-like consistency.
Adhesive collection
- For medium to large areas, use a single-disc floor machine (e.g., polisher) equipped with Tynex bristle pads
- For small areas or detailed sections, use a scraper with a blade
Vacuum the waste using a wet/dry vacuum cleaner with HEPA filters.
Alternatively, spread REMOVECO ABSORBENT POWDER, a mineral-based powder with high absorbency, over the surface until a wet soil-like consistency is achieved. Then collect the material using a HEPA-filter vacuum.
Finishing step
Apply a final layer of REMOVECO GEL across the entire surface.
Allow it to act for 30–60 minutes.
Go over the surface again with the single-disc floor machine equipped with Tynex bristles.
Vacuum the floor using a wet/dry HEPA-filter vacuum cleaner.
Dispose of the collected waste in accordance with applicable regulations.
Average Product Consumption
- REMOVECO GEL: 1 L/m²
- REMOVECO ABSORBENT POWDER: 1.5 kg/m²
Bill of Quantities – Adhesive removal with REMOVECO GEL
| No. | Description of works | Quantity (m²) |
Unit price (€) |
Total amount (€) |
|---|---|---|---|---|
| 1 | Application by roller or spray of a certified Type D encapsulating solution, such as CEMBLOK BASE by Geo Hydrica s.r.l., on the surface of the vinyl-asbestos (VA) tiles.l. Approx. consumption: 1 L/m² |
|||
| 2 | Mechanical removal and packaging of the vinyl-asbestos tiles in certified and approved containers. | |||
| 3 | Disposal of the packaged waste in accordance with asbestos waste regulations. | |||
| 4 | Application of a layer of non-hazardous gel, such as REMOVECO GEL by Geo Hydrica s.r.l., using a soft-bristle broom, notched squeegee, or airless spray pump. Approx. consumption: 0.8–1 L/m² |
|||
| 5 | Waiting time: 6 hours to allow REMOVECO GEL to act. Site management costs apply during this phase. |
|||
| 6 | Adhesive removal: Treat the surface using a single-disc floor machine equipped with Tynex pads. For corners and detailed areas, remove the adhesive manually using blade scrapers. | |||
| 7 | Waste collection: Spread REMOVECO ABSORBENT POWDER (Geo Hydrica s.r.l.) over the treated surface until a wet soil-like consistency is achieved. Then vacuum the waste using a wet/dry vacuum cleaner with HEPA filters and appropriate brush attachment. Approx. consumption: 1.5 kg/m² |
|||
| 8 | Disposal of asbestos-containing waste in compliance with applicable regulations. | |||
| 9 | Adhesive finishing: Apply a final layer of REMOVECO GEL, allow to act for 30 minutes, then go over the surface again with the single-disc floor machine equipped with Tynex pads. Approx. consumption: 0.2–0.5 L/m²² |
|||
| 10 | Final waste collection: Vacuum the surface using a HEPA-filter wet/dry vacuum cleaner with brush attachment. Dispose of the collected waste according to regulations. Approx. consumption: 1.5 kg/m² |
Recommened tools
For optimal application, we recommend using a single-disc floor machine equipped with a Tynex bristle disc brush, which ensures effective adhesive removal. This type of floor machine is available for rental at €40/day.
For those who prefer to purchase it, units are available for sale at our headquarters.
Averege execution times - REMOVECO system
| Phase | Activity | Personnel | Avaerage daily output |
|---|---|---|---|
| Application | Application of REMOVECO GEL on vinyl-asbestos adhesive | 2 operators | 1.000 m² |
| Initial removal | Floor machine pass + vacuuming | 2 operators | 700 m² |
| Finishing | Final REMOVECO GEL application + floor machine + vacuuming | 2 operators | 300 m² |
Our products for vinyl - asbestos removal
